X波段雷达前门防护技术研究

为了提高X波段雷达的带外抑制能力,在传统方形环孔的基础上,设计了一种新型带通FSS单元。运用谱域法对这种新型单元的传输系数进行了数值计算。计算结果表明:该新型频率选择表面(FSS)的工作带宽为8～12 GHz,该新型单元具有极好的角度稳定性。入射角度φ从0°到90°变化时,工作带宽漂移量不超过100 MHz;入射角度θ从0°到45°变化时,工作带宽漂移量不超过400 MHz。应用于X波段(8～12 GHz)雷达天线上,可提高其带外抗干扰的能力。     

面向任务的导弹测试性需求分析与指标确定

针对当前缺乏科学合理的理论和方法确定导弹系统级测试性指标的现状,提出一种面向任务需求的测试性指标确定方法.将导弹任务剖面划分为贮存、出库、部署和发射四个阶段,并提出各个阶段相应的测试需求;分别建立基于贮存可用度、战斗准备任务成功率、部署战备完好率和发射任务成功率为性能要求的测试性需求子模型,给出各个性能指标与测试性参数...     

南水北调中线工程安阳段渠坡换填土的强度特性研究

为了分析南水北调中线工程安阳段渠坡的稳定性,对该渠坡换填土在不同含水率下进行了不固结不排水三轴剪切试验.研究结果表明:剪切速率对基质吸力的影响较大,而对强度的影响较小;通过比较确定了合适的剪切速率;含水率相同的试样在不同围压下的强度值在pf -qf坐标上呈良好的线性关系;得到了试样在不同含水率下的总强度指标,建立了总内...     

一种适用于UHF频段军事卫星通信的高效传输方案

特高频(UHF)频段由于其良好的通信性能,正愈发广泛地应用于军事卫星通信,尤其是卫星移动通信,然而由于该频段信道所受干扰和固有衰落的限制,UHF在卫星通信中的应用并非一帆风顺。如何提高系统通信容量及在干扰环境下的信道可用率是目前UHF频段军事卫星通信发展所面临的主要挑战。文章在分析UHF频段卫星通信特点的基础上,简要介绍了具有良好性能的低密度校验码(LDPC)码和连续相位调制(CPM)方式,并结合UHF频段的卫星信道特点,提出了一种新的发展对策——LDPC+CPM+FH的串行级联通信方案,最后对方案进行了建模和计算机仿真。     

概率分布模型的飞机战备完好率评估与预测

飞机战备完好率是军用飞机战斗力的重要体现.在分析目前部队常用的飞机战备完好率算法缺陷的基础上,建立了基于概率分布的飞机战备完好率计算模型,该模型体现了飞机任务可靠性、维修性与战备完好性之间的关系.以某型飞机为例,通过分析飞机任务可靠度,利用飞机可靠性、维修性、保障性及作战训练任务的历史统计数据,依据概率分布模型对飞机的...     

Effect of organo-modified montmorillonite nanoclay on mechanical,thermal and ablation behavior of carbon fiber/phenolic resin composites

The mechanical, thermal and ablation properties of carbon phenolic (C-Ph) composites (Type-I) rein-forced with different weight percentages of organo-modified montmorillonite (o-MMT) nanoclay have been studied experimentally. Ball milling was used to disperse different weight (wt) percentages (0, 1,2,4,6 wt.％) of nanoclay into phenolic resin. Viscosity changes to resin due to nanoclay was studied. On the other hand, nanoclay added phenolic matrix composites (Type-II) were prepared to study the dispersion of nanoclay in phenolic matrix by small angle X-ray scattering and thermal stability changes to the matrix by thermogravimetric analyser (TGA). This data was used to understand the mechanical, thermal and ablation properties of Type-I composites. Inter laminar shear strength (ILSS), flexural strength and flexural modulus of Type I composites increased by about 29％, 12％and 7％respectively at 2 wt.％ addition of nanoclay beyond which these properties decreased. This was attributed to reduced fiber volume fraction (％Vf) of Type-I composites due to nanoclay addition at such high loadings. Mass ablation rate of Type-I composites was evaluated using oxy acetylene torch test at low heat flux (125 W/cm2) and high heat flux levels (500 W/cm2). Mass ablation rates have increased at both flux levels marginally up to 2 wt.％ addition of nanoclay beyond which it has increased significantly. This is in contrast to increased thermal stability observed for Type-I and Type-Ⅱ composites up to 2 wt.％addition of nanoclay. Increased ablation rates due to nanoclay addition was attributed to higher insulation effi-ciency of nanolcay, which accumulates more heat energy in limited area behind the ablation front and self-propagating ablation mechanisms triggered by thermal decomposition of organic part of nanoclay.     

A novel formulation of material nonlinear analysis in structural mechanics

This article demonstrates a novel approach for material nonlinear analysis. This analysis procedure eliminates tedious and lengthy step by step incremental and then iterative procedure adopted classically and gives direct results in the linear as well as in nonlinear range of the material behavior. Use of elastic moduli is eliminated. Instead, stress and strain functions are used as the material input in the analysis procedure. These stress and strain functions are directly derived from the stress-strain behavior of the material by the method of curve fitting. This way, the whole stress-strain diagram is utilized in the analysis which naturally exposes the response of structure when loading is in nonlinear range of the material behavior. It is found that it is an excellent computational procedure adopted so far for material nonlinear analysis which gives very accurate results, easy to adopt and simple in calculations. The method eliminates all types of linearity assumptions in basic derivations of equations and hence, eliminates all types of possibility of errors in the analysis procedure as well. As it is required to know stress distribution in the structural body by proper modelling and structural idealization, the proposed analysis approach can be regarded as stress-based analysis procedure. Basic problems such as uniaxial problem, beam bending, and torsion problems are solved. It is found that approach is very suitable for solving the problems of fracture mechanics. Energy release rate for plate with center crack and double cantilever beam specimen is also evaluated. The approach solves the fracture problem with relative ease in strength of material style calculations. For all problems, results are compared with the classical displacement-based liner theory.     

N、P源对微生物法处理石油烃效果的影响

在微生物法处理石油烃的过程中,微生物对N、P源的供给非常敏感,不同的微生物对不同的N、P源的生物利用度是不相同的,N、P源的选择对降解效果有较大影响,所以有必要对最佳的N、P源进行筛选。对N、P源的逸择和加入量对降解效果的影响进行了研究,确定了最佳的N、P源分别为(NH4)2SO4、KH2PO4。在(NH4)2SO4、KH2PO4的质量浓度分别为100mg／L和60mg／L时,废水中石油烃的去除率最高。     

基于实际案例的导弹装备战斗损伤评估

指出了基于实际案例的通用导弹装备战斗损伤评估内容及特点,提出了战斗损伤评估的量化标准,定义了战损率的概念;采用向量夹角余弦方法综合出了导弹装备各级组件的战损率及车辆的战损量化值,并通过实例证明了该方法具有所需信息量小、主客观综合性强、评估方法易于仿真实现等优点.     

基于PON技术的多站雷达数字光纤传输系统设计

提出一种多站雷达体系雷达数据光纤传输系统的方案设计和实现方法。与传统雷达使用的光纤传输系统不同,而是采用技术较新的基于无源光网络PON的实时数据通信系统,这是无源光网络技术在多传感器实时通信领域的首次应用。在系统设计中利用先进的光电子和在编程技术,实现了点对多点雷达数据光纤传输,提高了信号传输质量,同时系统具有动态接入和扩容的能力。